DOB LED Installation

Aug 10, 2025

Leave a message

Keywords: AC COB LED, COB LED installation, How to solder COB LED, LED soldering guide, LED solution, how to install LED, heatsink installation, LED silicone application, LED maintenance, LED lighting solution.

 

DOB LED, as a highly integrated and driverless AC COB LED module, is widely used in home lighting, commercial lighting, industrial lighting, outdoor lighting and other scenarios. It simplifies the assembly process of lighting fixtures by integrating the driver circuit with the LED light source (DOB LED stands for Driver-on-Board LED), while also having the advantages of small size, light weight, low cost, high reliability, and long lifespan. To ensure stable operation of the LED and avoid safety risks, it is necessary to strictly follow the following steps, including material preparation, welding specifications, heat dissipation treatment, and safety protection.

 

1. Preparation before installation

Before the installation, please ensure that the following materials and tools are prepared:

• Electric soldering iron

• Lead free solder wire

• Kraft 704 or 705 sealing silicone (other brands are also available)

• One power plug wire that meets local standards (Let's take EU plug as an example below)

• DOB LED module (Lets take our 50W DOB LED as an example below)

• Heatsink (recommended to match the heat dissipation power with LED)

• Thermal conductive silicone grease (choose the appropriate thermal conductivity coefficient according to the heat dissipation density, generally choose 1.5-2.0 thermal conductivity coefficient for low LED power, and we suggest to choose a coefficient of 3.0 or above for high-power LEDs exceeding 200W).

image001

 

2. Operation steps (including soldering specifications)

1) Pre-soldering treatment of soldering iron

Before soldering, melt a small amount of lead-free solder wire on the tip of the soldering iron to form a smooth solder joint for smoother soldering in the next step. This can improve soldering efficiency and avoid pseudo soldering or poor soldering joint.

2) Pre-soldering treatment of LED pads

To reduce the difficulty of subsequent soldering and ensure the firmness of the solder joints, it is necessary to perform pre-soldering treatment on the solder pads of the DOB LED module:

Adjust the temperature of soldering iron to be around 400 ℃, and use the soldering iron tip to solder a small section of spherical tin wire (with a diameter of about 1-2mm) to the "L" pad (live wire) and "N" pad (neutral wire) of the LED, respectively, to ensure that the spherical tin wire does not fall off or avoid pseudo soldering, and to avoid poor contact during subsequent wiring.

image003
image004

 

3. Pre-treatment of heatsink

DOB LED will generate heat while working. Poor contact between the led board and the heatsink will cause poor heat dissipation, leading to increased light decay, shortened lifespan, and even damage. Therefore, it is necessary to preprocess the heatsink:

1) Clean the surface of heatsink: Wipe the contact surface between the heatsink and LED with anhydrous alcohol to remove oil stains and oxide layers.

2) Coating silicone grease: Apply a small amount of thermal conductive silicone grease at the center point of the metal substrate on the back of the DOB LED, and use a scraper to smooth it out thinly, with a thickness of about 0.1 mm. The thinner and more uniform the thermal conductive silicone grease is, the better the heat dissipation effect will be; Do not apply too thickly to avoid affecting the heat dissipation effect.

3) LED fixation: Align the screw holes of led board with the corresponding holes of the heatsink, pre-tighten two screws diagonally first, and then complete the remaining screws to ensure seamless fit. During this process, it is important to avoid pressing the light-emitting surface area of the LED accidentally to prevent any chip damage.

 

4. Wire connection

1) Distinguishing wires: First, clarify the polarity of each wire and the corresponding position for each wire to be soldered:

  • Live wire (L) connecting to the brown wire
  • Neutral wire (N) connecting to the blue wire
  • Protective Earth (PE) connecting to the yellow green wire
image006

2) Soldering operation: Gently touch the soldering iron tip to the connection place between the pad and the wire. After the pre-soldered spherical solder wire melts, push in a small amount of lead-free solder wire slowly to form a smooth spherical solder joint (its diameter should be about 2-3mm);

3) Cooling Check: After soldering, wait 5-10 seconds for the solder joint to cool down naturally. Gently pull the wire to confirm there is no any looseness. If the solder joint is cracked or cold, reheat and re-solder it then.

4) Fixing the Ground Wire: It is recommended to install a ground collar on the ground wire. This allows for direct screwing the wire to the heatsink (i.e., the lamp shell) for a very secure connection. If without a ground collar, a large screw with a nut can also be used to tighten the bare ground wire.

Note:

a. The color standards for wires may vary between different countries or regions. Please ensure that all wire connections are made according to local electrical regulations.

b. When soldering, ensure that the polarity of the wires is strictly observed to avoid reverse connection, which may cause the LED to remain dim light even when the switch is off. (Generally, the switch is to control the on and off of the live wire. If the wires connected in reverse, when the switch is turned off, actually its the neutral wire disconnected, and the live wire still remains connected, so the lamp will not be turned off completely.)

image008
image009

 

5. Sealing and Insulation treatment

To prevent moisture and dust from entering the input pads of LED, thus preventing short circuits and electric shock accidents, it is necessary to seal the wiring position:

1) Use Kraft 704 or 705 sealing silicone to seal the LED input pads.

After sealing, ensure that the silicone covers the metal contacts completely, forming an insulating protective layer.

2) Don't forget to also seal the ground wire with silicone to strengthen its connection and prevent the risk of electrical leakage. This treatment provides waterproofing, dustproofing, and shock proofing, and is suitable for outdoor or humid environments.

3) Place the assembled heatsink in a well-ventilated environment at room temperature (20-25°C) and allow the silicone to cure (generally 0.5-1 hour is sufficient; performing a burn-in test can accelerate the curing process). Avoid touching the silicone before it cures.

image012

 

6. Power-On Test

1) Confirm the LED Voltage: First, confirm the voltage type of the LED (AC 220V or AC 110V).

For AC 220V LED, inputting AC110V voltage will not cause any damage;

but for AC 110V LED, if inputting high voltage AC 220V above, there will be a high probability risk of dead light.

2) Input the corresponding voltage range of AC 220-240V or AC 110-130V. Power on and check the power is correct or not, and all LEDs are illuminated or not.

 

7. Steady-State Temperature Test

After 10 minutes of operation, touch the heatsink to confirm that it is not high temperature abnormally (normal temperature ≤ 60-80°C). After 1-2 hours of operation, test the temperatures of three locations to ensure proper heat dissipation. Proper heat dissipation ensures LED lifespan:

Steady-state temperature for the LED surface of fluorescent glue: Recommended temperature below 105°C.

If the glue surface temperature exceeds 120°C, there is a risk of glue cracking and yellowing, and the LED chip may become loose and solder joints may become poorly soldered, which will lead to dead light.

Steady-state temperature for the backside of LED board: Recommended temperature between 70-90°C.

The backside temperature for the bottom of LED board should not be too high, otherwise heat cannot be conducted away, resulting in lamp failure.

Steady-state temperature for the outer surface of heatsink: Recommended temperature between 55-75°C.

Try not to exceed 80°C. Otherwise, the temperature of LED glue surface would exceeded 120°C, there will be the risk of lamp failure.

 

8. Common Problems and Precautions

1) The LED can not be turned on

Check if the input voltage is correct or if there is any pseudo soldering for wires.

2) Rapid light decay of LED and decrease in brightness

Confirm whether the power of the heatsink matches the power of the LED, and whether the thermal grease is evenly applied; If the heat dissipation space of the lamp is narrow, it is necessary to add more heat dissipation holes or fans to assist in heat dissipation.

3) Poor heat dissipation

If the LED temperature is too high during operation, check whether the heatsink is matched and whether the thermal grease is evenly applied.

4) Environmental adaptability

If used outdoors or in high humidity environments, it is recommended that the overall lighting structure should have a protection level of IP65 or above.

 

9. Daily maintenance suggestions

Check the cleanliness of the lamp shell surface every 6-12 months, blow off dust with compressed air, and avoid dust accumulation that affects the heat dissipation effect;

Check the sealing of outdoor lighting fixtures every 3 months to avoid water ingress caused by silicone cracking.

Under correct installation and good heat dissipation conditions, DOB LEDs can have a long lifespan of over 50000 hours.

 

DOB LED is becoming an important choice in lighting solutions due to their high integration and low maintenance cost advantages. Proper installation and use can not only ensure its performance and lifespan, but also significantly improve the safety and reliability of the lighting system.

If you encounter any problems during the LED installation process, please feel free to visit WELCOB website to contact our technical support team, and we will provide you with professional service.